Compliance

Central Kitchen & Food Factory SOPs: Line to Dispatch

SOPs for central kitchens and food factories: line start-up, GMP zones, CCP monitoring, allergen changeover, batch records, traceability and cold chain.

A production line with labelled trays, a probe thermometer, a batch label with a barcode and a tablet showing a critical control point log

When a restaurant group opens its tenth branch, the central kitchen usually follows: one site that preps, cooks, portions and dispatches to every outlet so the branches assemble rather than cook. The same logic drives food factories supplying retailers and aggregators. Either way, the operation has stopped being a kitchen and become a small manufacturing plant, and the procedures have to change with it.

In a branch kitchen, a mistake affects tonight’s covers. In a central kitchen, a mistake affects every outlet’s covers for three days and is traceable to a batch, a line and a shift. That is why central kitchen and factory SOPs are heavier on records, traceability and critical control points than anything a branch needs. Here are the ones that matter, the standard for each and the proof each leaves. For the method see how to write an SOP; for definitions, our guide to standard operating procedures.

This article describes common good practice and is not legal or food-safety advice. Requirements vary by country, authority and product category; confirm with the relevant regulator and your food-safety consultant.

1. Hygiene zoning and GMP entry

Covers: zone definitions (low-risk, high-risk, high-care), entry procedures per zone (hand wash, boot change, hair and beard covering, PPE colour by zone), visitor and contractor entry, movement rules between zones.

Standard: no entry to high-risk without the full procedure; zone PPE colours never mixed; visitor log complete.

Proof: entry checklist per shift per zone; visitor and contractor sign-in; periodic GMP audit scores.

2. Line start-up and pre-operational inspection

Covers: pre-op cleanliness inspection of each line and piece of equipment (visual and, where used, ATP swab), equipment function checks, calibration verification of probes and scales, metal detector or X-ray test pieces, water and sanitizer checks, first-off product check.

Standard: no production until the pre-op inspection passes; detectors tested with all test pieces and logged; probes verified against a reference.

Proof: pre-op inspection record with pass/fail per item and photo on fails; detector test log with time and test-piece results; calibration log.

3. Receiving and raw material control

Covers: approved supplier check, certificate of analysis where required, temperature probe per chilled category, frozen state, date and lot capture, allergen identification and segregation on receipt, quarantine of non-conforming goods.

Standard: chilled 0–5°C, frozen at or below -18°C, every lot number recorded against the delivery, allergen-containing materials stored in designated areas.

Proof: readings and lot numbers per line item, CoA filed to the lot, quarantine log with photos. The generic receiving SOP is written out in our SOP template; the factory version adds lot capture.

4. Critical control point monitoring

Covers: each CCP from your HACCP plan: typically cooking core temperature, cooling time and temperature, chilled storage, metal detection, and for some products pH or water activity; monitoring frequency, critical limits, who monitors, verification.

Standard: the critical limits from your plan (for example core 75°C; cooling from 60°C to 21°C within two hours and to 5°C within a further four; chilled storage at or below 5°C); every monitoring point completed at the defined frequency.

Proof: CCP records with reading, time, batch, monitor and verifier; deviation records with corrective action and disposition of affected product.

CCP monitoring is where paper records fail most expensively. Readings written up at the end of a shift are not monitoring; they are fiction with a date on it. Digital capture at the point of measurement with an automatic timestamp is the single biggest improvement a central kitchen can make, and it is what regulators across the Gulf increasingly expect to see; our guides to food safety SOPs in Saudi Arabia and in the UAE cover the regulatory context.

5. Allergen changeover

Covers: production scheduling by allergen (allergen-free first), line clearance at changeover, cleaning and verification (visual, swab where used), label and packaging reconciliation, sign-off before the next product starts.

Standard: no changeover without documented line clearance and cleaning verification; packaging for the previous product removed from the line and counted.

Proof: changeover record with clearance checklist, cleaning verification result, packaging reconciliation, two signatures.

6. Batch records and traceability

Covers: the batch record for every production run (recipe version, raw material lots used, quantities, process readings, yield, packaging lot, operators), batch coding on finished product, one-step-back and one-step-forward traceability, mock recall procedure and frequency.

Standard: every finished batch traceable to its raw material lots and to its dispatch destinations; mock recall completes within a defined time (four hours is a common internal target) at least annually, often quarterly.

Proof: complete batch records; mock recall reports with time to trace and reconciliation percentage.

7. Portioning, packing and labelling

Covers: portion weights and tolerances, packaging specification per product, label content (product, allergens in bold, batch code, production and use-by dates, storage instructions, outlet if dedicated), label verification against the product, metal detection after packing where applicable.

Standard: weights within tolerance checked at defined intervals; every label verified by a second person at start of run and on any change; no unlabelled product leaves the line.

Proof: weight check records, label verification sign-off with a photo of the label, detector pass per batch.

8. Cleaning and sanitation (master sanitation schedule)

Covers: daily, weekly and periodic cleaning of lines, equipment, floors, drains, walls, ceilings and high-level surfaces; clean-in-place where used; chemical concentrations and contact times; verification (visual, ATP, micro swabs on a schedule).

Standard: schedule completed on time; verification results within limits; out-of-limit results trigger re-clean and re-test.

Proof: completion per item with end-state photos on key equipment; verification results logged by location; trend review monthly.

9. Preventive maintenance and calibration

Covers: maintenance schedule per asset (refrigeration, ovens, blast chillers, slicers, detectors, scales), lubricant and material food-grade controls, calibration schedule for probes, scales and detectors, breakdown reporting and maintenance hygiene clearance before the line restarts.

Standard: every asset serviced on schedule; calibration within tolerance; no restart after maintenance without hygiene clearance.

Proof: maintenance records per asset, calibration certificates and logs, clearance sign-offs. Requests and approvals for breakdowns run through requests and approvals in Opscale.

10. Pest control and waste

Covers: pest-control contractor schedule and findings, trend review, proofing checks, waste segregation (food, packaging, hazardous), waste area hygiene, oil disposal records.

Standard: contractor visits on schedule with reports filed; no uncontrolled proofing gaps; waste area clean to photo standard daily.

Proof: contractor reports, proofing inspection with photos, waste area photo daily.

11. Dispatch and cold chain to outlets

Covers: order picking against outlet orders, dispatch temperature checks, vehicle pre-cooling and temperature logging, loading sequence, delivery documentation with batch codes, outlet receipt confirmation, returns and rejections handling.

Standard: product dispatched at or below 5°C (chilled) or -18°C (frozen); vehicles pre-cooled and logged; every delivery note carries batch codes; outlet confirms receipt temperature.

Proof: dispatch temperature per order, vehicle log, delivery note photo, outlet receiving record (which is the branch’s receiving SOP closing the loop).

12. Training, competency and internal audit

Covers: induction and GMP training per role, CCP monitor training and sign-off, refresher schedule, internal audit programme (GMP, HACCP verification, traceability), management review.

Standard: no one monitors a CCP without sign-off; internal audits completed on schedule with non-conformances closed.

Proof: training and competency records per person, audit reports with non-conformance tracking. See how to train staff on SOPs and prove compliance.

What is different about central kitchens and factories

  • Records are the product’s passport. Batch, lot, CCP and dispatch records must connect, or traceability fails when it is needed.
  • Verification is built in. Pre-op inspections, detector tests, swabs and second-person label checks are SOPs in their own right.
  • Changeover is a controlled event, not a pause between runs.
  • The outlets are your customers. The dispatch SOP and the branch receiving SOP should be designed together.

Running it as one system

Central kitchens supplying ten or fifty outlets need the SOPs, the records and the outlet-side checks in one place. In Opscale, procedures, HACCP plan documents and training videos live in the operations library; pre-op inspections, CCP monitoring, changeovers, sanitation and dispatch checks run as scheduled, role-based tasks with numeric limits and photo proof in tasks and checklists; deviations and corrective actions in the logbook; GMP and internal audits in inspections; and the executive dashboard shows completion and deviations by line, shift and outlet, alongside the branches’ receiving records. The AI checklist creator will turn your existing HACCP forms into structured tasks. More on how food manufacturers in the region use it on our factories and manufacturing page.

The branch kitchen runs on habit and a good chef. The central kitchen runs on records. Make them digital, at the point of measurement, and the records become both easier to keep and worth something when someone asks.

Related solutions

Ready to run tighter operations?

Join the teams replacing chaos with clarity. Book a 20-minute demo and see Opscale on your own workflows.

No credit card required · Works on web, iOS & Android